罗茨风机为您介绍罗茨风造组成。罗茨风机主要由四部分构成：机壳、墙板、叶轮、进出口消音器等。

　　Roots blower introduces the composition of Roots blower. The Roots blower mainly consists of four parts: casing, wall panels, impeller, inlet and outlet mufflers, etc.

　　1、叶轮:是罗茨鼓风机转动部分，分成二叶和三叶。如今，因为三叶的出气脉冲小、低噪、运行稳定等众多优势，已经渐渐替代了二叶罗茨鼓风机。

　　1. Impeller: It is the rotating part of a Roots blower, divided into two blades and three blades. Nowadays, due to its advantages such as small air pulse, low noise, and stable operation, the three bladed Roots blower has gradually replaced the two bladed Roots blower.

　　2、机壳：主要用于支撑墙板、叶轮、消音器和固定作用。

　　2. Shell: mainly used to support wall panels, impellers, mufflers, and for fixing purposes.

　　3、墙板：主要用于连接机壳和叶轮，并支撑叶轮的转动，及其端面密封的。

　　3. Wall panel: mainly used to connect the casing and impeller, support the rotation of the impeller, and seal its end face.

　　4、消音器：用于降低罗茨风机因气旋脉冲而引起的出入噪声。

　　4. Muffler: Used to reduce the inlet and outlet noise caused by cyclone pulses in Roots blowers.

　　罗茨鼓风机是一种体积式鼓风机，输送的风量与转速成比例。叶轮端面与鼓风机前后盖之间和鼓风机叶轮之间的间隙总是很小。在同步齿轮的推动下，风从鼓风机的进气口顺着机壳内壁输送到排出的一侧。

　　Roots blower is a volumetric blower that delivers air in proportion to its rotational speed. The gap between the impeller end face and the front and rear covers of the blower, as well as between the blower impeller, is always very small. Under the push of the synchronous gear, wind is transported from the inlet of the blower along the inner wall of the casing to the side where it is discharged.

　　今日风机将与大家一起拆解，看看罗茨鼓风机是由什么部件组成的。

　　Today, we will disassemble the fan together to see what components make up the Roots blower.

　　，一套完整的罗茨鼓风机包含:风机主机、共享基座、电机、电机杆、皮带盘、皮带盖、三通、减压阀、止压阀、气压表、入口消声器、出口消声器、抗震接头、防震垫、配套螺钉等。

　　A complete set of Roots blower includes: fan host, shared base, motor, motor rod, belt pulley, belt cover, tee, pressure reducing valve, check valve, pressure gauge, inlet muffler, outlet muffler, seismic joint, seismic pad, matching screws, etc.

　　除了配件和电机，罗茨鼓风机主机是技术含量和重要构成部分。一个好的主机头在使用中噪声相对较低，风量比较稳定。与其它罗茨鼓风机相比，其使用寿命能长达5年以上。在诸多罗茨鼓风机生产商中，机械技术凭着坚实基础和强大的生产实力，在罗茨鼓风机设计、制造和销售层面，变成罗茨鼓风机行业管理者。其生产的罗茨鼓风机合理，风量大，低噪，节能，性能优异，坚固耐用。

　　In addition to accessories and motors, the Roots blower host is a technologically advanced and important component. A good host head has relatively low noise and stable air flow during use. Compared with other Roots blowers, its service life can last for more than 5 years. Among many Roots blower manufacturers, mechanical technology, with a solid foundation and strong production capabilities, has become the industry manager in the design, manufacturing, and sales of Roots blowers. The Roots blower produced by it is reasonable, with large air volume, low noise, energy saving, excellent performance, and durability.

　　罗茨鼓风机主机主要由2组叶轮、一个汽缸、四个轴承、2个齿轮、2个端盖、一个齿轮罩、2个轴承座和其它部件构成。

　　The Roots blower main unit is mainly composed of 2 sets of impellers, 1 cylinder, 4 bearings, 2 gears, 2 end caps, 1 gear cover, 2 bearing seats, and other components.

　　配件清单图

　　Accessories List Diagram

　　罗茨风机分解图

　　Decomposition diagram of Roots blower

　　需要注意的是，罗茨鼓风机可分为两种类型:真空鼓风机和压送鼓风机。真空和压送罗茨鼓风机实质上没有太大的差别，他们是由主机的电机和配件组成的。不同的是，真空罗茨鼓风机遇有一个真空过滤桶。这是压送罗茨鼓风机没有用的。

　　It should be noted that Roots blowers can be divided into two types: vacuum blowers and pressure blowers. There is not much difference between vacuum and pressure fed Roots blowers, they are composed of the motor and accessories of the main unit. The difference is that the vacuum Roots blower has a vacuum filter barrel. This is useless for pressure fed Roots blowers.

　　真空式罗茨风机结构图

　　Structural diagram of vacuum Roots blower

　　以上是罗茨鼓风机基本结构。如果你想了解更多更多信息，请咨询风机。大家会给你更丰富详细的解释。掌握罗茨鼓风机制造后，通常是罗茨鼓风机维护和应用。罗茨鼓风机运作时要注意查验:电源、电压、电流值、压力、大气温度、排气温度、轴承温度、震动、噪声、油量、污渍水平、皮带张力等。，并留下记录卡，这对调研及早发现或出现问题的原因有很大帮助。出口闸阀不能用于调节风量，应改变转速或增送方法。

　　The above is the basic structure of Roots blower. If you want to learn more information, please consult the fan. Everyone will provide you with more comprehensive and detailed explanations. After mastering the manufacturing of Roots blowers, it is usually the maintenance and application of Roots blowers. During the operation of Roots blower, attention should be paid to checking: power supply, voltage, current value, pressure, atmospheric temperature, exhaust temperature, bearing temperature, vibration, noise, oil level, stain level, belt tension, etc. And leave a record card, which is very helpful for early detection or identification of the causes of problems during research. The outlet gate valve cannot be used to regulate air volume, and the speed or delivery method should be changed.

　　大家在罗茨鼓风机解剖图前边的文章中分享过。随着小系列数据的不断完善，罗茨鼓风机解剖图早已分类整理了。先放一张设计解剖图:

　　Everyone has shared in the article before the anatomical diagram of Roots blower. With the continuous improvement of small series data, the anatomical diagram of Roots blower has already been classified and organized. First, place a design anatomical diagram:

　　这张图是一张缩小后的小图，上面有标明的具体内容。由于之前的文章早已提及了，如果你想看大图和注明的内容，请点击这里。→_→由三叶罗茨鼓风成，下面小编还为大家整理了一张彩色三叶罗茨鼓风机解剖图，图为老罗茨鼓风机L型，如图所示:

　　This picture is a reduced image with specific content indicated on it. As mentioned in the previous article, if you would like to see the large image and the annotated content, please click here. → _ → Created by the Three Leaf Roots blower, the following editor has also compiled a colored anatomical diagram of the Three Leaf Roots blower, which is an L-shaped old Roots blower, as shown in the picture:

　　因为样式的原因，很多罗茨鼓风机生产商早已对其进行了整改设计。罗茨鼓风造基本一致，但不同的生产商和不同的生产商之间有微小的差别。供参考。下列解剖图为三叶罗茨鼓风机内部透视框架图，如下所示:

　　Due to the style, many Roots blower manufacturers have already made improvements to their designs. Roots blower production is basically the same, but there are slight differences between different manufacturers. For reference only. The following anatomical diagram is an internal perspective frame diagram of a three blade Roots blower, as shown below:

　　这可以更立体的展示，叶轮、齿轮、轴承、油箱等零部件能够清晰的看到。随着风机数据的不断完善，还整理了一张四分之一的截面图，如图所示:

　　This can provide a more three-dimensional display, where components such as impellers, gears, bearings, and oil tanks can be clearly seen. With the continuous improvement of fan data, a quarter section diagram has also been compiled, as shown in the figure:

　　三叶罗茨鼓风机结构和二叶罗茨鼓风机基本一致，由于罗茨鼓风机还有其他结构类型，如密集式、水冷型等。，并且还有其他构造的解剖图，可是罗茨鼓风机主体框架图大部分是这样的。

　　The structure of the three leaf Roots blower is basically the same as that of the two leaf Roots blower, as there are other structural types of Roots blowers, such as dense and water-cooled. And there are also anatomical diagrams of other constructions, but most of the framework diagram of the Roots blower body is like this.

　　型号介绍:(-200罗茨鼓风机)。罗茨鼓风机采用先进的设计技术和高精密制造。选用内部回流技术、出口降噪技术、三叶摆线叶型、拼装密集技术等科研开发。髙压罗茨鼓风机性能可靠，应用范围广，密封结构各种类型，满足氨气力输送、粉煤灰输送、选矿厂、化工、焦煤等其它污染和浸蚀标准。是49客户～商品在98kPa下。流量范围：1.63～101m3/min；变压范畴：9.8～98kPa

　　Model introduction: (-200 Roots blower). Roots blower adopts advanced design technology and high-precision manufacturing. We have conducted scientific research and development on internal reflux technology, export noise reduction technology, three blade cycloid profile, and dense assembly technology. The high-pressure Roots blower has reliable performance, wide application range, and various types of sealing structures, meeting other pollution and erosion standards such as ammonia pneumatic conveying, fly ash conveying, mineral processing plants, chemical industry, coking coal, etc. 49 customers~The product is under 98kPa. Flow range: 1.63-101m3/min; Transformer range: 9.8-98kPa

　　动力传送方式包含皮带连接和连轴器连接，灵活方便；鼓风机200罗茨鼓风机压力平稳，低噪，震动小。压力可见，便于监管200罗茨鼓风机工作状态。配件性能优异。集成集中的设计特点使之体型小、流量、以人为中心拼装方法；鼓风机罗茨鼓风机配备:依据作用不同，200罗茨鼓风机轴承配备既能满足风机规定，又能达到高质量。200罗茨鼓风机集风机、进出口消音器、电机、过滤器、弹性接头、闸阀、逆止阀、压力计为一体。

　　The power transmission method includes belt connection and coupling connection, which are flexible and convenient; The 200 Roots blower has stable pressure, low noise, and minimal vibration. The pressure is visible, making it easy to monitor the working status of the 200 Roots blower. Excellent accessory performance. The integrated and centralized design features result in a small size, high flow rate, and a human centered assembly method; Blower Roots blower equipment: Depending on its function, the 200 Roots blower bearing equipment can meet the requirements of the fan and achieve high quality. The 200 Roots blower integrates a fan, inlet and outlet mufflers, motor, filter, elastic joint, gate valve, check valve, and pressure gauge.

　　本文由 罗茨鼓风机  友情奉献.更多有关的知识请点击  http://www.sdyshjx.com/  真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Roots blower For more related knowledge, please click http://www.sdyshjx.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.